Hasselblad H2F Uživatelský manuál stáhnout pdf (Strana 29)

 Ensure you press on the centre of the button, not on the lever.

 You cannot remove a magazine if the darkslide is not closed.

 If the ﬁlm holder is inadvertently removed mid-ﬁlm, then exposed frames will naturally be

lost due to light fogging. However, if the ﬁlm holder is quickly re-inserted, the ﬁlm will auto-

matically be advanced by three frames to position fresh unexposed ﬁlm. The ﬁlm counter

will also correspondingly add on three frames to the original number recorded before the

ﬁlm holder was removed.

Removal

Ensure that the darkslide indicator on the magazine shows red (signifying that the

darkslide is closed). Firstly push the lever of the magazine release button to the right (il-

lus 1) and while maintaining that position press the centre of the button rmly inwards

towards the camera body (illus 2) to nally release the magazine.

Attachment

Position the magazine retention groove onto the magazine support on the camera body

ensuring that they are correctly positioned. Swing the magazine towards the camera

body and rmly press into place with a click. If there is resistance, the magazine retain-

ing catch on the camera has probably been inadvertently released. In that case, push the

release button again to reset the catch.

You can attach and remove the magazine with or without the lm holder in place. If you

just want to change to a new lm, you can remove and reload the lm holder without

having to remove the whole magazine.

Attaching and removing the magazine 3, 4

You cannot remove a magazine from the camera body if the magazine darkslide is not in

place, (when the magazine darkslide indicator on the magazine shows white). Neither can

you withdraw the magazine darkslide when the magazine is not attached to the camera.

Both these restrictions therefore prevent accidental lm loss caused by fogging.

Battery replacement 1, 2

Release the lm holder by folding out the lm holder key and rotating it 90° in a counter-

clockwise direction. Withdraw the lm holder completely. On the bottom plate on the

inside of the lm magazine housing you will nd a slotted circular battery cover. Insert

a small coin or similar into the slot and rotate the cover about 20° in a counter-clockwise

direction. e cover will be freed and the battery can be removed. Replace with a fresh

CR2032 / 3V lithium (or equivalent) battery. Observe the polarity and ensure the positive

(+) face is uppermost and replace the cover (ensure the retaining lugs are inserted in the

battery compartment slots), locking it into place by rotating it in a clockwise direction

until it stops. If you inadvertently insert the battery incorrectly, the lm magazine will

not be damaged though it will not function. Try to avoid touching the surface of the

battery with your bare ngers as sweat residue can decrease the electrical conductivity

of the battery casing and might cause corrosion.

Aer battery replacement, the magazine’s parameters return to the default settings

(Barcode, 120, Data-on, Count up).

Battery

e magazine uses a battery to retain information and settings when unattached from the

camera. When attached to the camera body, the magazine takes its power requirements

from the camera batteries. e magazine battery will normally be eective for 1-2 years

depending on use (o camera illumination, for example).

When the battery is in a very low condition, (approx... 1 month of use le), a low-battery

symbol appears on the magazine LCD as a warning.

e magazine will continue to function with no battery power le as long as it remains

attached to the camera body. However, when detached, the settings will not be stored.

Operation

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 85 86

Komentáře k této Příručce

Žádné komentáře

Hasselblad H2F Uživatelský manuál Strana 29

Komentáře k této Příručce